הבלוג של phoneparts

phoneparts

עדכונים:

פוסטים: 238

החל ממאי 2017

The taptic engine and loudspeaker are the exchangeable parts of iPhone XS’s. Here we would like to demonstrate you how to replace the iPhone XS taptic engine & loudspeaker, and we hope this could be a tutorial guide for you if you are trying to fix your iPhone XS at home. Let’s get the new replacement partsand repair tools ready, and get started.

1. Tear down iPhone XS and take off the display screen

 1.1 Power off the phone, take out the iPhone XS SIM card tray and loosen the two pentalobe screws on the bottom

 1.2 Use hot air gun blowing the edge on the display, in 80℃ for about 2 minutes

 1.3 Use the suction cup to make a gap between the display and the frame, then insert the ultra-thin plastic sheet to slice around the gap to separate the display screen from the phone
1.4 Pry and flip over the display screen carefully, loosen the four Y-type screws and a Phillips screw, remove the metal bracket with tweezers

1.5 Disconnect the battery flex cable first, then the touch flex cable and the display flex cable. Remove the display screen away after it is entirely disconnected

2. Replace the iPhone XS taptic engine and loudspeaker

2.1 Loosen the seven Phillips screws and the Y-type screw, then remove the small metal brackets which are for fixing the taptic engine modules carefully with tweezers

 2.2 Disconnect the iPhone XS loudspeaker flex cable and then use spudger and tweezers to pry up and remove the loudspeaker. The taptic engine is connected under the loudspeaker, just be careful and don’t bring it up

 2.3 Take down the taptic engine after the loudspeaker is removed

 2.4 Place the new replacement iPhone XS taptic engine in the phone and connect the flex cable

 2.5 Install the new loudspeaker into the phone and connect the flex cable

 2.6 Place the small metal brackets back and fix them with the eight screws

3. Reinstall the iPhone XS display screen

 3.1 Connect the flex cables back, includes the display flex cable, the touch flex cable and the battery flex cable for the last

 3.2 Turn on the phone and test the function of the new replaced elements. Test the screen 3D touch to check the vibration response. Go to Settings >> Sounds & Haptics. Play ringtone and adjust the volume to see if the loudspeaker is normal

 3.3 Disconnect the flex cables as the orders in Step 1.5 and remove the display screen, clear out the frame adhesive glue

 3.4 Attach a new iPhone XS frame adhesive back to the phone

 3.5 Connect and reinstall the display screen back, place the metal cover for fixing it with the five screws.

Remember, your iPhone XS would be not 100% waterproof after repaired. Be patient and careful if you are the first time to repair your iPhone. Any questions will be answered as long as you leave your comments below, or you can email us if you have any questions about the iPhone XS replacement parts in the process above.

עוד מהבלוג של phoneparts

Samsung Galaxy S9 review

I've been testing Samsung's new Galaxy S9 and larger, slightly stepped-up Galaxy S9 Plus($839.99 at Amazon.com) for over a week. And while I'm 85 percent certain that these beautiful, powerful phones are two of the best that money can buy, the remaining 15 percent of me is disappointed that the world's largest Android brand couldn't do a little better. From a bird's eye view, I see...

תגובות

תגיות:

פורסם לפני 2 years

Google Pixel 2 release date, news and rumors

Another leak indicates that previous images of the purported Pixel 2 we've seen might not be accurate to how it will look. We hope you weren't too attached to those thin bezels. Recently, the purported Pixel 2 has shown up in the flesh, seeming to confirm some design elements we've seen, as well as that the big bezels are likely to make a return, whether you like it or not. Last, but not...

תגובות

פורסם לפני 3 years
תצוגה מקדימה

How to Replace iPad Pro 10.5” Touch Screen and Digitizer Assembly

Step 1: Tear down and separate the iPad Pro 10.5 touch screen and digitizer assembly  1.1 Turn off the iPad, hot air gun blowing on the screen edge to soften the frame adhesive glue, then use a thin steel pry tool to make a gap between the screen and the frame  1.2 Use hard plastic triangle plectrum to slice around the gap slowly, you may need three or more plectrums...

תגובות

פורסם לפני 5 months

תגובות

טופ 20 - בלוגים

מתחברים לסלונה

הכתבות הנקראות ביותר

אסור לפספס

בחזרה למעלה